Dranetz Xplorer Podręcznik Użytkownika Strona 78
- Strona / 290
- Spis treści
- BOOKMARKI
Oceniono. / 5. Na podstawie oceny klientów
4-10
Communications
Communications
Communication
interface setup
Communications Settings is where instrument-specific information is entered to allow
the PX5 to communicate to external devices using the optional
Isolated
Communications
Module assemblies or modem (see related information on Chapter 9 Downloading
Events).
Continued on next page
Action... Result...
STEP 1: From the Instrument
Settings Setup Menu screen, press
Communications.
•Press Enable
Communications
to
activate/deactivate the
communications port. External
communication devices connect to
the PX5 mainframe via the optical
serial data port. The optical serial
data port connector is located on
the left side of the instrument.
• Press to enter the communications
Device Address
from 01 to 32 for
use with the optional Fiber Optic
to Ethernet adapter.
• Select the corresponding
Baud
Rate
to set connection speed.
Default baud rate is 11520.
•Press
External Modem
Connected
if you want to activate
communications via an external
modem.
Press
Change
to modify
the modem initialization string.
The string must begin with “AT”.
Dranetz
recommends using
the same brand and model of
modem at both ends of the
communications link. See Chapter
9 Downloading Events for
instructions on modem
connections.
•Press
IP
to configure your
Ethernet settings and allow the
PX5 to operate on the network.
Proceed to Step 2 on page 4-11.
•Press
OK
to accept changes in
communications settings.
•Press
Cancel
to discard changes in
communications settings and
return to Instrument Settings
menu.
MARK159
NOTE: For instructions on how to physically
connect to NodeLink using the external
communications devices, see Chapter 9
Downloading Events.
- PowerXplorer 1
- ADVERTENCIA 3
- Safety Summary 4
- Safety Summary, Continued 5
- Statements and Notices 7
- Continued 8
- Table of Contents 9
- Table of Contents, Continued 10
- Dranetz PowerXplorer 14
- CHAPTER 1 15
- Getting Started 15
- Unpacking the PX5 17
- Standard Accessories 18
- Top View 19
- Front View 19
- Rear View 19
- Bottom View 19
- 1 2 3 5 6 7 8 9 10 11 124 20
- CH 1/ Getting Started 21
- 2 3 5 64 22
- Rear view 23
- PX5 Features 26
- Basic Operation 28
- MARK001b 29
- Basic Operation, continued 30
- CHAPTER 2 31
- PX5-11.vsd 35
- PX5-12.vsd 36
- PX5-13.vsd 37
- Connecting Current Probes 39
- PX5-14.vsd 40
- PX5-15.vsd 42
- CHAPTER 3 43
- View Real Time Data 43
- Turning Channels On/Off 45
- Checking Input Range 46
- Standard Meter Tab 48
- CH 3/ View Real Time Data 49
- Distortion Meter Tab 50
- Unbalance Meter Tab 53
- Advanced Power Meter Tab 54
- Harmonic Graph 58
- Harmonic Detail 59
- Harmonic Options 60
- Harmonic List 62
- Phasor Screen 64
- Phasor Rotation 65
- Phasor Rotation, continued 66
- CHAPTER 4 69
- Time and Date Settings 71
- Select Language 73
- Set Display Preferences 74
- Touch Screen Calibration 75
- Turn Threshold Beeper On/Off 77
- Data Card 80
- CH 4/ Instrument Settings 83
- CHAPTER 5 85
- Start Menu 85
- Current Probe Selection 92
- Scale Factor Setup 94
- Nominal Values 98
- Nominal Values, continued 100
- Mode of Operation 101
- Monitoring Mode 102
- Advanced Options 103
- Site Name/Memory Card 104
- Action... Result 105
- CH 5/ Start Menu 107
- Section C 108
- Turning Monitoring On/Off 109
- Section D 118
- Section E 119
- Overview 119
- Card Error Messages 120
- CHAPTER 6 121
- Advanced Setup Options 121
- Advanced Options Menu 122
- Transient Limit 123
- High Frequency Transients 124
- Recording Transients 125
- RMS Variation Limit 129
- Waveform Capture 134
- Characterizer Options 135
- Journal Limit 136
- Journal Limit, continued 138
- CH 6/ Advanced Setup Options 139
- -10%); Medium Voltage 144
- (11 kVrms). LV is defined 144
- 1kV to 35kV nominal 144
- CHAPTER 7 145
- View Event Data 145
- Overview, continued 146
- Section A 148
- Event Data Display 149
- Event Activity Graph 150
- Event List 151
- Event Detail 153
- Event Options 158
- Section B 161
- Trend Display 162
- Trend Setup 163
- CH 7/ View Event Data 165
- CHAPTER 8 167
- Continued on next page 169
- EN50160 Compliance Limits 171
- CH 8/ Reports 173
- Compliance History 177
- Compliance History, continued 178
- Event Satistics 179
- Event Statistics, continued 180
- Panel Setup Options 183
- Panel Operation 185
- CHAPTER 9 189
- Downloading Events 189
- Communications 190
- CH 9/ Downloading Events 191
- Viewing Events via DranView 199
- DranView 200
- with HASP 200
- Top Side Bottom Side 202
- APPENDIX A 205
- Optional Accessories 205
- Software Accessories List 212
- APPENDIX B 215
- Technical Specifications 215
- Interfaces 217
- Measured Parameters 218
- Computed Parameters 220
- cos 0 221
- VARVARVARVAR ++= 222
- VAVAVAVA ++= 222
- Channels 225
- 61000-4-30 225
- TR2500 Current Probe 226
- TR2510 Current Probe 227
- APPENDIX C 229
- Battery Specifications 230
- Battery Safety Precautions 231
- External Battery Charger 232
- Battery Pack Replacement 234
- Battery removal 235
- APPENDIX D 237
- User Replaceable Parts List 237
- APPENDIX E 239
- Common Circuit Connections 239
- AVERTISSEMENT 240
- Single Phase 245
- Split Phase 246
- 3 Phase, Four Wire Wye 247
- 3 Phase 2-Watt Delta 249
- Generic Circuit 250
- APPENDIX F 259
- Event Classification 259
- APPENDIX G 263
- PX5 Menu Structure 263
- LEVEL 001 264
- Home Screen 264
- LEVEL 100/1 265
- Start Menu - Automatic Setup 265
- LEVEL 100/2(a) 266
- Start Menu - Wizard Setup 266
- LEVEL 100/1(b) 267
- LEVEL 100/3 268
- LEVEL 100/4 269
- LEVEL 100/5 269
- LEVEL 150 270
- Instrument Settings 270
- LEVEL 108 271
- Circuit Type Selection 271
- LEVEL 200 272
- Scope Mode 272
- LEVEL 300/1 273
- Meter Mode - Standard 273
- LEVEL 300/2 274
- Meter Mode - Distortion 274
- LEVEL 300/3 275
- LEVEL 300/4 275
- Meter Mode - Unbalance 275
- LEVEL 300/5 276
- Meter Mode - Advanced 276
- LEVEL 220 277
- Harmonics 277
- LEVEL 240 278
- Phasor Display 278
- LEVEL 112_101 279
- Advanced Options 279
- LEVEL 112_201 280
- MARK112_207 281
- MARK112_208 281
- MARK112_214 281
- LEVEL 112_501(a) 282
- LEVEL 112_501(b) 283
- Level 112_601 284
- Journal Interval 284
- LEVEL 112_701 285
- EN50160 Options 285
- LEVEL 400 286
- TO LEVEL 401 286
- LEVEL 401 287
- LEVEL 430 288
- LEVEL 470(a) 289
- Reports - EN50160 289
- To Level 470(b) 289
- LEVEL 470(b) 290
- Reports - Status 290
Powiązane produkty i podręczniki dla Pomiary, testowanie i kontrola Dranetz Xplorer
(60 strony)© 2020, manymanuals.pl. Wszelkie prawa zastrzeżone. | 0.049 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentarze do niniejszej Instrukcji